Is anyone using a red dot sight on their CZ 550 ?

[SkullKeeper]

Skull, I would say lower than a scope. But of course it depends on your face height , neck height and check weld. View attachment 659417

Ahhh, ok good deal - thanks for the photo !

 

[Hunt anything]

I did, so bought a comb riser from Midway USA. It came with several different pads so I could get the correct fit.

I should add on my current.416 I have a picatinny rail that the RMR is attached to. Just easier for me to take off and put a Trijicon scope on it. That’s the reason for the need to raise the comb for me anyway.

 

[Mark A Ouellette]

I like the looks of that SRO , and I’d say the 2.5 MOA would be good?

Select the smallest dot available, a 1 MOA in the SRO.
Why? As one increases the intensity of the dot on a sunny day, the dot size grows.
Add to that any astigmatism one may have making the dot even larger and egg shaped, your dot blob may vary.

Does anyone find that the RMR/SRO on the AHR mount are taller than a “low mount” scope ?

I shot some snapshots of a RMR, SRO, and 1" scope rings for a CZ 550.

Height from base to top of Warne 1" scope ring is 45+mm

Bottom of AHR mount for RMR on CZ 550 with a SRO 43+mm

Bottom of AHR mount for RMR on CZ 550 with a RMR 34+mm

For comparison, a RMR and SRO in AHR mounts on a CZ 550

 

[SkullKeeper]

Ok thank you very much Mark! I like the shorter RMR and 1 MOA is much better !

 

[deewayne2003]

Ok thank you very much Mark! I like the shorter RMR and 1 MOA is much better !

I’ve got an RMR 1moa with AHR QD mount on my BRNO 602 and it’s a game changer!

 

[SkullKeeper]

I’ve got an RMR 1moa with AHR QD mount on my BRNO 602 and it’s a game changer!

Thank you ! Im on it !

 

[Altitude sickness]

Skull, if you’re not sure. I’ll send you my SRO 1 with 1 MOA to try out. Look up the Marks post on the pros and cons of the SRO1 vs the smaller RMRs

 

[ftrovato]

Select the smallest dot available, a 1 MOA in the SRO.
Why? As one increases the intensity of the dot on a sunny day, the dot size grows.
Add to that any astigmatism one may have making the dot even larger and egg shaped, your dot blob may vary.


I shot some snapshots of a RMR, SRO, and 1" scope rings for a CZ 550.

Height from base to top of Warne 1" scope ring is 45+mm
View attachment 659424

Bottom of AHR mount for RMR on CZ 550 with a SRO 43+mm
View attachment 659425

Bottom of AHR mount for RMR on CZ 550 with a RMR 34+mm
View attachment 659426

For comparison, a RMR and SRO in AHR mounts on a CZ 550
View attachment 659427

Thanks. Well demonstrated! I went with the lowest RMR and a 1" dot on your recommendation a few years ago and used it on buffalo last fall. It worked very well and yes lower mount helps keep your head lower and aids in a faster recover for next shot (if you keep the rifle mounted to your shoulder).

 

[DWB]

I had a custom mount made for an Aimpoint Micro H1 on my ZKK602 in 450 Rigby.

Don't think you can go much lower.

 

[RR 314]

I went with the AHR fixed option on the .550 Magnum. . .

 

[Pirkan]

If there´s a good mount available where you´re at you might want to look into an Aimpoint Acro. It has a closed emitter so it´s not as sensitive to dust etc as some other suggestions and it´s designed to be mounted on pistol slides (which are subject to very high acceleration) so the recoil of a 505 should not be a problem at all. I might be a little biased because it´s one of very few internationally known gun related Swedish companies but I don´t think anyone can honestly call Aimpoints bad.

 

[Frederik]

My Trijicon 1 MOA left on my 458 Lott mounted with predator apex mount next to @DWB 's 450 Rigby.

 

[SkullKeeper]

Skull, if you’re not sure. I’ll send you my SRO 1 with 1 MOA to try out. Look up the Marks post on the pros and cons of the SRO1 vs the smaller RMRs

That is a very gracious offer and I thank you very much for that - after seeing Mark’s pictorial of the sizes I think I will lean towards the smaller RMR after all. Again, I appreciate the offer sir !